So what can you use for a growbed?

The short answer is almost anything, but there are a number of things you should take into consideration, including whether your growbed will be located inside or outside. It goes without saying that the growbed needs to be waterproof, but you need to make absolutely certain of this.

It also needs to be strong enough to hold the media and the water - depending on the size of the growbed this could equate to a fairly significant amount of pressure... an important consideration if you decide to make a growbed yourself.

Any watertight, food-safe, fish-safe container can be used, and depending on the size of your whole aquaponics system that will leave you with several choices.

•Small systems can use food containers, plastic containers from the DIY store or IKEA, wooden boxes with a suitable liner - almost anything that will fit the size of your fish tank.

•Medium sized systems can use cut up IBC totes, Rubbermaid-type water troughs, animal feed troughs, concrete mixing troughs and similar things.

•Larger sized systems can use multiple units from above, hand built and lined wooden growbeds, and of course, commercially available aquaponics growbeds.

Aquaponics Growbed Materials

A growbed can be made out of a wide variety of materials but care should be taken to make sure it fulfills certain criteria. A growbed should be safe to use first and foremost, and should be made of a materials that will not leak unwanted chemicals into the water, or that will affect the pH of the water.

A growbed should ideally be made of a material that blocks out the sun, as direct sunlight can promote algae growth and can be detrimental to plant roots. If the growbed is being used outside then it will also need to be UV stabilized to ensure that it will not degrade in the sunlight and leach chemicals into the system.

Commonly used materials would be certain plastics, wood, fibreglass and anything with suitable waterproof liners. Concrete can also be used but care needs to be taken to seal the concrete first as concrete can affect negatively affect the water chemistry of your system

Growbed depth and Size

An aquaponic growbed needs to be the right size to fit your fish tank volume. It needs to be able to provide adequate mechanical filtration and biological filtration for the nutrient-rich water, and so you should always consider the growbed and the fish tank together and use appropriately corresponding sizes.

A common rule of thumb is to use a 1-1 ratio. The growbed volume should be equal to the fish tank volume. This is by no means a hard-and-fast rule but serves as an outline guide.

The plants in your system are also part of your filtration process and so you must ensure that you have adequate surface growing area relative to the same of your fish tank. As a rule of thumb, if 1000 litres of water needs approximately 1 meter cubed of growbed media volume for filtration, then if your growbed is 25cms deep you will need a surface area of approximately 1m x 4m to ensure that there is approximately 1 meter cubed of media volume.

•The surface layer (5cms) - this is above the waterline and should not be wet - this reduces loss of water through evaporation.

•The root layer (20cms) - this is where your roots will be growing and where most plant activity will take place. This is layer is normally regularly flooded and drained.

• The solids layer (5cms) - this is where the solid waste will collect in your system and which will usually be constantly flooded with water.

From these layers we can work out a kind of 'ideal depth' of 30cms or 12 inches. Whilst this depth has been proven to be highly effective it is by no means then only depth that can be used. Aquaponics systems have been shown to work equally well with growbed depths of as little as 10cms or so - but care needs to be taken to always ensure that you have sufficient volume to provide adequate filtration for your system.

...and finally...

At the end of the day, don't feel that you have to use a specific size and type of growbed. As long as it is safe, strong and appropriately sized for the system that you are building, then it will be worth trying out.

If you can build a growbed that is 30cms deep then you can be confident that this is a tried-and-tested depth that has been proven to provide very effective results - but you can also rest assured that a shallower or deeper growbed is also likely to give you good results.

Keep in mind that of the four functions that a growbed traditionally performs, three of those are related to filtration, and so your main consideration when choosing a growbed size, is to ensure that it is able to provide adequate filtration for your own aquaponics system, including adequate planting area.

Don't be afraid to be creative - as long as you can follow the guidelines noted above, then try anything that you have to hand - or anything that you think would look great. Put safety first and you can't really go too far wrong.